Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)
Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
26-02-2011, 10:31 AM
Post: #1
DC MOTOR CONTROL USING CHOPPER
DC MOTOR CONTROL USING CHOPPER
INTRODUCTION

Development of high performance motor drives are very essential for industrial applications. A high performance motor drive system must have good dynamic speed command tracking and load regulating response. DC motors provide excellent control of speed for acceleration and deceleration. The power supply of a DC motor connects directly to the field of the motor which allows for precise voltage control, and is necessary for speed and torque control applications. DC drives, because of their simplicity, ease of application, reliability and favorable cost have long been a backbone of industrial applications. DC drives are less complex as compared to AC drives system. DC drives are normally less expensive for low horsepower ratings. DC motors have a long tradition of being used as adjustable speed machines and a wide range of options have evolved for this purpose. Cooling blowers and inlet air flanges provide cooling air for a wide speed range at constant torque. DC regenerative drives are available for applications requiring continuous regeneration for overhauling loads. AC drives with this capability would be more complex and expensive. Properly applied brush and maintenance of commutator is minimal. DC motors are capable of providing starting and accelerating torques in excess of 400% of rated [3]. D.C motors have long been the primary means of electric traction. They are also used for mobile equipment such as golf carts, quarry and mining applications. DC motors are conveniently portable and well fit to special applications, like industrial equipments and machineries that are not easily run from remote power sources D.C motor is considered a SISO (Single Input and Single Output) system having torque/speed characteristics compatible with most mechanical loads. This makes a D.C motor controllable over a wide range of speeds by proper adjustment of the terminal voltage. Now days, Induction motors, Brushless D.C motors and Synchronous motors have gained widespread use in electric traction system. Even then, there is a persistent effort towards making them behave like dc motors through innovative design and control techniques. Hence dc motors are always a good option for advanced control algorithm because the theory of dc motor speed control is extendable to other types of motors as well [3]. Speed control techniques in separately excited dc motor:
By varying the armature voltage for below rated speed.
By varying field flux should to achieve speed above the rated speed.
Different methods for speed control of DC motor:
Traditionally armature voltage using Rheostatic method for low power dc motors.
Use of conventional PID controllers.
Neural Network Controllers.
Constant power motor field weakening controller based on load-adaptive multi- input multi- output linearization technique (for high speed regimes).
Single phase uniform PWM ac-dc buck-boost converter with only one switching device used for armature voltage control. Using NARMA-L2 (Non-linear Auto-regressive Moving Average) controller for the constant torque region. Large experiences have been gained in designing trajectory controllers based on self-tuning and PI control. The PI based speed control has many advantages like fast control, low cost and simplified structure. This thesis mainly deals with controlling DC motor speed using Chopper as power converter and PI as speed and current controller.
CHOPPER
2.1. DC CHOPPER A chopper is a static power electronic device that converts fixed dc input voltage to a variable dc output voltage. A Chopper may be considered as dc equivalent of an ac transformer since they behave in an identical manner. As chopper involves one stage conversion, these are more efficient [2]. Choppers are now being used all over the world for rapid transit systems. These are also used in trolley cars, marine hoist, forklift trucks and mine haulers. The future electric automobiles are likely to use choppers for their speed control and braking. Chopper systems offer smooth control, high efficiency, faster response and regeneration facility [2]. The power semiconductor devices used for a chopper circuit can be force commutated thyristor, power BJT, MOSFET and IGBT.GTO based chopper are also used. These devices are generally represented by a switch. When the switch is off, no current can flow. Current flows through the load when switch is “on”. The power semiconductor devices have on-state voltage drop of 0.5V to 2.5V across them. For the sake of simplicity, this voltage drop across these devices is generally neglected [2]. As mentioned above, a chopper is dc equivalent to an ac transformer, have continuously variable turn’s ratio. Like a transformer, a chopper can be used to step down or step up the fixed dc input voltage
2.2. PRINCIPLE OF CHOPPER OPERATION A chopper is a high speed “on" or “off” semiconductor switch. It connects source to load and load and disconnect the load from source at a fast speed. In this manner, a chopped load voltage as shown in Fig. is obtained from a constant dc supply of magnitude Vs. For the sake of highlighting the principle of chopper operation, the circuitry used for controlling the on, off periods is not shown. During the period Ton, chopper is on and load voltage is equal to source voltage Vs. During the period Toff, chopper is off, load voltage is zero. In this manner, a chopped dc voltage is produced at the load terminals
2.3. CONTROL STRATEGIES [2] The average value of output voltage Vo can be controlled through duty cycle by opening and closing the semiconductor switch periodically. The various control strategies for varying duty cycle are as following: 1. Time ratio Control (TRC) and 2. Current-Limit Control. These are now explained below.
2.3.1. Time ratio Control (TRC) In this control scheme, time ratio Ton/T(duty ratio) is varied. This is realized by two different ways called Constant Frequency System and Variable Frequency System as described below:
1. CONSTANT FREQUENCY SYSTEM [2]
In this scheme, on-time is varied but chopping frequency f is kept constant. Variation of Ton means adjustment of pulse width, as such this scheme is also called pulse-width-modulation scheme.
2. VARIABLE FREQUENCY SYSTEM [2]
In this technique, the chopping frequency f is varied and either (i) on-time Ton is kept constant or (ii) off-time Toff is kept constant. This method of controlling duty ratio is also called Frequency-modulation scheme.

DOWNLOAD FULL REPORT
http://ethesis.nitrkl.ac.in/1677/2/amir_...report.pdf
26-04-2012, 10:14 AM
Post: #2
RE: DC MOTOR CONTROL USING CHOPPER
PLEASE SEND A PPT ON DC MOTOR CONTROL USING CHOPPER
Rating DC MOTOR CONTROL USING CHOPPER Options
Share DC MOTOR CONTROL USING CHOPPER To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : chopper, dc motor control using chopper ppt, chopper controlled dc motor, dc motor speed control using chopper ppt, dc chopper uses, dc motor control by chopper, pdf seminar on ac dc drives, ppt of dc motor speed control using chopper, dc motor control using chopper, chopper controled dc motor ppt, chopper device which convert fixed dc to varying dc, speed control of dc mptor by chhopar, ppt on dc motor controlled by buck chopper, dc motor control chopper ppt, dc motor control by using chopper, dc choppers doc, control of d c drives pdf ppt doc, choppers in power electronics ppt, speed control of dc motor using chopper ppt, eletrical samenar topic in chopper,

[-]
Quick Reply
Message
Type your reply to this message here.


Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  POWER GRID CONTROL WITH FAULT DETECTION SEMINAR REPORT project maker 0 137 19-09-2014 03:08 PM
Last Post: project maker
  An Intelligent Automated Door Control System Based on a Smart Camera Seminar Report seminar code 0 116 08-09-2014 10:03 AM
Last Post: seminar code
  GSM Based Power Meter Reading And Control System Seminar Report seminar code 0 124 04-09-2014 02:33 PM
Last Post: seminar code
  AC Motor Testing and Predictive Maintenance Seminar Report seminar code 0 70 21-08-2014 11:12 AM
Last Post: seminar code
  MOTOR CONTROLS project maker 0 90 07-08-2014 10:57 AM
Last Post: project maker
  TRANSFORMER LESS AUTOMATION HOME APPLIANCE CONTROL SYSTEM seminar code 0 121 21-07-2014 12:25 PM
Last Post: seminar code
  UNIVERSAL MOTOR SPEED CONTROL USING IGBT seminar code 0 159 18-06-2014 04:39 PM
Last Post: seminar code
  WIRELESS ELECTRICAL APPLIANCES CONTROL SYSTEM USING IR COMMUNICATION project maker 0 148 17-06-2014 12:06 PM
Last Post: project maker
  NEURAL NETWORKS IN PROCESS CONTROL ppt seminar projects maker 0 399 12-06-2014 12:53 PM
Last Post: seminar projects maker
  HYBRID PETRI NET MODELING OF TRAFFIC FLOW AND SIGNAL CONTROL pdf seminar post 0 144 28-05-2014 02:58 PM
Last Post: seminar post
This Page May Contain What is DC MOTOR CONTROL USING CHOPPER And Latest Information/News About DC MOTOR CONTROL USING CHOPPER,If Not ...Use Search to get more info about DC MOTOR CONTROL USING CHOPPER Or Ask Here

Options: