Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)
Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
08-03-2011, 04:55 PM
Post: #1
FABRICATION OF PLASTIC INJECTION MOULDING DEVICE

.doc  REWRITE.doc (Size: 64.5 KB / Downloads: 220)
INTRODUCTION
The Polymer material are converted into plastic and used as tubes, sheets, foams, rods, adhesives, etc. The theological properties, softening, tempering, stability, the size and shape are important in describing the method. These methods are different kinds of plastics. Broadly speaking the method may be discussed under the following headings.
ABSTRACT
The project deals about the injection moulding machine. The main principle is to compress the plastic material in a barrel and the compression motion is developed by rotating the screw rod and sliding nut arrangement. The plastic material is heated by the heater surrounding the barrel. Then it is converted into molten state. The molten plastic is injected through the nozzle in barrel to the die by the compression force. After completing this process, we will get the product from the die. Commercial products like bushes, couplings, switches etc, can be produced.
FABRICATION TECHNIQUES :
1. MOULDING PROCESS
2. FOAMING PROCESS
MOULDING PROCESS :
In this process the plastic are fabricated under the effect pressure and heat and both thermoplastics and thermosetting plastics may be starting materials.
INJECTION MOULDING :
Thermoplastics are produced by this method. In this the material is softened by heating and the hot softened plastic is forced under high pressure into the mold, when it is set by cooling and the mold is ejected.
FOAMING PROCESS :
This involves the blowing of a volatile organic liquid. Which is entrapped into a polymer network resulting in the formation of foamed plastics. Foamed polystyrenes are produced in this process.
WORKING PRINCIPLE
The injection moulding process is best suited for producing articles made of thermoplastic materials. Here the equipment cost is relatively high but the main attraction is the amenability of the injection moulding process to a high production rate. In injection – moulding machine is shown in the process consists of feeding the compounded plastic material as granules, pellets or powder through the hopper at definite time intervals into the hot horizontal Cylinder where it gets softened. Pressure is
applied through a motorised driven piston to push the molten material through a cylinder into a mould fitted at the end of the cylinder. While moving through the hot zone of the cylinder, a device called torpedo helps spread the plastic material uniformly around the inside wall of the hot cyclinder sand thus ensures uniform heat distribution. The molten plastic material from the cylinder is then injected through a nozzle material from the cylinder in then injected through a nozzle into the mould cavity.
The mould used in its simplest form, is a two part system. One is movable part and the other stationary. The stationary part is fixed to the end of the cylinder while the movable part can be opened or locked on to the stationary part. By using a mechanical locking device, the mould is proper held in position as the molten plastic material is injected under a pressure as high as 1500 kg/ cm. The locking device has to be very skillfully designed in order to withstand high operating pressures. Further more, a proper flow of the molten material to the interior regions of the mold is achieved by preheating the mould to an appropriate temperature. Usually this temperature is slightly lower than the softening temperature of theplastic material under going moulding.
After the mould is filled with the molten material under pressure. Then it is cooled by cold water circulation and then opened so as to eject the molded articles. The whole cycle could be repeated several time either manually of in an automated mode.
08-04-2011, 03:42 PM
Post: #2
RE: FABRICATION OF PLASTIC INJECTION MOULDING DEVICE
you are need to read following reports to get better idea about injection moulding and similar process (some page posses report and ppt)
http://www.seminarprojects.com/Thread-a-...ode=linear
http://www.seminarprojects.com/Thread-fa...ing-device
http://www.seminarprojects.com/Thread-ho...ng-machine

Please Use Search http://seminarprojects.com/search.php wisely To Get More Information About A Seminar Or Project Topic
28-12-2012, 07:45 PM
Post: #3
RE: FABRICATION OF PLASTIC INJECTION MOULDING DEVICE
Hey guys,
This is Ezra,and I am going to do my design fabrication project on plastic injection molding device,particularly the injection part.I need some technical help regarding the design especially calculations.So send me some tipsWink
Rating FABRICATION OF PLASTIC INJECTION MOULDING DEVICE Options
Share FABRICATION OF PLASTIC INJECTION MOULDING DEVICE To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : moulding, injection mold, idea for mechanical engineering project plastic, plastic injection molding process, mechanical engineering projects information plastic, mechanical engg project ppt pellet, injection moulding, moulding process for fabrication of thermosetting plastics, what is fabrication of plastic, plastic engineering project, projects in plastics for mechanical engg, project ideas in plastics, ppt on plastic molding fabrication process, project for mechanical engineering injection moulding, fabrication of plastics ppt, latest mechanical seminar topics in injection moulding pdf, seminars on injection molded plastic for mechanical engg,

[-]
Quick Reply
Message
Type your reply to this message here.


Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  DESIGN AND FABRICATION OF DOUBLE ACTING HACK SAWING MACHINE UNDER BY SCOTCH YOKE study tips 6 2,718 Yesterday 07:17 PM
Last Post: Guest
  Design and fabrication of sucker rod pump jaseelati 0 22 Yesterday 01:54 PM
Last Post: jaseelati
  DESIGN AND FABRICATION OF MODEL OF AIR CUSHION VEHICLE jaseelati 0 25 Yesterday 01:52 PM
Last Post: jaseelati
  Indicator device for gear shifting in automobiles jaseelati 0 31 19-09-2014 02:24 PM
Last Post: jaseelati
  Small Scale Injection Moulding jaseelati 0 56 18-09-2014 04:04 PM
Last Post: jaseelati
  Plastic Rapid Prototype Technology Used for New Design to Replace KNEE JOINT jaseelati 0 24 18-09-2014 03:38 PM
Last Post: jaseelati
  Determination,Analysis and Reduction of defects in injection moulding jaseelati 0 17 18-09-2014 01:21 PM
Last Post: jaseelati
  LASER INDUCED IGNITION OF GASOLINE DIRECT INJECTION ENGINES PROJECT REPORT seminar code 0 91 13-09-2014 04:20 PM
Last Post: seminar code
  DESIGN AND FABRICATION FABRICATION OF MOTORIZED MOTORIZED SCREW JACK FOR A FOUR WHEEL seminar code 0 42 13-09-2014 02:33 PM
Last Post: seminar code
  Mechanical Lifting Device Using Automobile (scooter) subin.e 0 112 05-09-2014 04:45 PM
Last Post: subin.e
This Page May Contain What is FABRICATION OF PLASTIC INJECTION MOULDING DEVICE And Latest Information/News About FABRICATION OF PLASTIC INJECTION MOULDING DEVICE,If Not ...Use Search to get more info about FABRICATION OF PLASTIC INJECTION MOULDING DEVICE Or Ask Here

Options: