Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)
Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
08-05-2012, 04:31 PM
Post: #1
Field Programmable Gate Array (FPGA) full report
Field Programmable Gate Array (FPGA)

.pdf  Field Programmable Gate Array (FPGA).pdf (Size: 162.5 KB / Downloads: 65)
1 Introduction
Field-Programmable Gate Arrays (FPGAs) are pre-fabricated silicon devices that can be electrically
programmed to become almost any kind of digital circuit or system [2]. They have many advantages
over Application Specific Integrated Circuits (ASIC). ASICs are designed for specific application using
CAD tools and fabricated at a foundry. Developing an ASIC takes very much time and is expensive.
Furthermore, it is not possible to correct errors after fabrication. In contrast to ASICs, FPGAs are
configured after fabrication and they also can be reconfigured. This is done with a hardware description
language (HDL) which is compiled to a bit stream and downloaded to the FPGA. The disadvantages of
FPGAs are that the same application needs more space (transistors) on chip and the application runs
slower on a FPGA as modern as the ASIC counterpart. Due to the increase of transistor density FPGA
were getting more powerful over the years. On the other hand the development of ASICs was getting
slower and more expensive. Therefore FPGAs are increasingly applied to high performance embedded
systems.
2 FPGA Structures
2.1 Basic Structure

In the chapter the basic structure of a FPGA will be described. Xilinx is one of the biggest FPGA
manufacturer. A Xilinx FPGA is made up of three basic blocks:
• CLB: The Configurable logic blocks are were the user specific functions are calculated.
• IOB: The Input/Output block make it possible to connect the FPGA to the other elements of the
application
• Interconnect: Interconnect is essential for writing between CLB and from IOBs to CLBs.
The CLBs are located at the center of the chip and the IOBs on the periphery. The interconnect is
necessary to implement several designs on the FPGA. The distributed configuration memory controls the
behavior of the CLBs and IOBs by storing the program. Next the implementations of CLBs, interconnect
and IOBs are described more in detail.
CLB Figure 1 shows a simplified CLB of a Xilinx FPGA. A CLB is used to implement custom combinational
or sequential logic. It is composed of a lookup table (LUT) controlled by 4 inputs to
implement combinational logic and a D-Flip-Flop for sequential logic. A MUX is used to select
between using the output of the combinational logic directly and using the output of the Flip-Flop.
One CLB is programmed by downloading the truth table of the logical function to the LUT (16
bit) and the control bit of the MUX (1 bit). By using multiple copies of the this structure any
combinational and sequential logic circuit can be implemented.
The figure only shows a very simplifies version of a CLB slice. In real a CLB is considerable
more complicated. To speed up additions extra logic for a carry chain is provided. Furthermore,
1
additional MUX are provided, so that the D-Flip-Flop can bis user without and in conjunction with
the LUT. Additionally the LUT can also be used as memory.
Once the CLB slices have been configured to implement logical functions they have to be connected
to implement bigger logical function. This is realized by programmable interconnect points (PIP)
showed at the right side in figure 1. It is a pass through transistor. The gate of the transistor is
connected to the memory. If that memory bit is set to one the ends of the transistor are logically
connected, otherwise no connection is made. Therefore different connection can be achieved by
loading the memory.
Figure 1: Configurable logic block (CLB) [1]
Interconnect Multiple copies of CLB slices are arranged in a matrix on the surface of the chip. The
CLBs are connected column-wise and row-wise. At the intersections of columns and rows are programmable
switch matrices (PSM). This can be seen in figure 2. In this figure the output of one
CLB is connected with the inputs of two other CLBs. The signal passes through three PIPs and two
PSMs. While the PSMs make the FPGA versatile, they slow down the signals. Therefore FPGA
implementation become considerable slower then their ASIC counterparts. Therefore FPGA designers
added many other interconnect in addition to PIPs and PSMs. Some architectures implement
nearest neighbor routs. There are also routes that skip some PSM. Furthermore, there are extra
routes for e.g. reset lines or clock lines.
Figure 2: Programmable interconnect [1]
IOB Input/output blocks are used to get the signals into the FPGA and out of the FPGA. Figure 3
shows a simplified IOB. Each IOB can be used as and input and output depending on the state of
the output enable (OE). If OE is set to one the IOB acts as an output, otherwise as an input. The
OE bit can be programmed statically or set to the output of a CLB. IOBs contain D-Flip-Flops for
2
latching the input and output signals. The latches can be bypassed by appropriately programmed
MUXs.
Figure 3: Input/Output block
Additionally to the described basic block the FPGA has a distributed configuration memory. The
memory locations are distributed over the chip and need to be loaded to configure the FPGA. Special
I/O pins that are not configurable by the user are used to load the program to the memory.
2.2 Modern FPGAs
In the previews section the basic building blocks of a FPGA were described. Additionally to these blocks
modern FPGAs have additional units that make the design of applications easier and more efficient.
Small memories and arithmetic units are difficult to implement on CLBs. Therefore modern FPGAs
provide embedded memories and embedded logic blocks for arithmetic calculations. The most common
arithmetic calculation is the multiplication, but many other operations can be provided. The advantage
of embedded logic blocks are better speed and space. Additionally embedded memories are easier to interface
than extern memories. DSP applications are often good targets for implementation on FPGA. Thus
manufacturer add embedded block to be useful for implementing DSP functions, e.g. multipliers. Furthermore,
they provide DSP logic designated for streaming data applications. FPGA often communicate
with microprocessors. Because of that reason, embedded processor cores are added to many FPGAs. The
main advantage of embedded microprocessors is the reduction of the latency of communication between
microprocessor and the FPGA. The Xilinx 4 family has support for additional operations configured by
the designer and implemented by CLBs with th auxiliary processing unit (APU) interface. In contrast
to embedded processors, soft cores are build directly on the FPGA fabric. The advantages are that they
are configurable and the clock can be the same as that of the FPGA. Furthermore, soft processor cores
are easier to interface. The big disadvantage is the slower clock rate.
2.2.1 The Xilinx Virtex-6 FPGA family
Virtex-6 the newest FPGA family from Xilinx. It is divided into the LXT, SXT and HXT sub-family.
Each sub-family contains a different ratio of features to address the needs of many logic designs:
• Virtex-6 LXT FPGAs: High-performance logic with advanced serial connectivity
• Virtex-6 SXT FPGAs: Highest signal processing capability with advanced serial connectivity
• Virtex-6 HXT FPGAs: Highest bandwidth serial connectivity
CLBs possess a LUT which can be configured as one 6-input LUT or two 5-input LUTs. The LUT also
can be used as 64 bit RAM or 2 32 bit RAMs.
Every Virtex-6 FPGA has between 156 and 1064 dual-port block RAMs, each storing 36 Kbits. Each
block RAM has two completely independent ports that share nothing but the stored data.
All Virtex-6 FPGAs have many dedicated, full-custom, low-power DSP slices combining high speed
with small size, while retaining system design flexibility.
Each DSP48E1 slice fundamentally consists of a dedicated 25 18 bit two’s complement multiplier and a
48-bit accumulator, both capable of operating at 600 MHz. The multiplier can be dynamically bypassed,
and two 48-bit inputs can feed a single-instruction-multiple-data (SIMD) arithmetic unit (dual 24-bit
3
add/subtract/accumulate or quad 12-bit add/subtract/accumulate), or a logic unit that can generate
any one of 10 different logic functions of the two operands. The slice provides extensive pipelining and
extension capabilities that enhance speed and efficiency of many applications. Every FPGA of the family
contains a System Monitor circuit providing thermal and power supply status information. Sensor outputs
are digitized by a 10-bit analog-to-digital converter (ADC). This fully tested ADC can also be used to
digitize up to 17 external analog input channels. All but one Virtex-6 device has between 8 to 72 gigabit
transceiver circuits. Each GTX transceiver is a combined transmitter and receiver capable of operating
at a data rate between 155 Mb/s and 6.5 Gb/s. An integrated Ethernet MAC block is easily connected to
the FPGA logic, the GTX transceivers, and the SelectIO resources. All but one FPGAs of the Virtex-6
family include at least one integrated interface block for PCI Express technology.
The XC6VHX5651 is an advanced FPGA of the Virtex-6 family. It consists of 566784 logic cells and
88560 CLB slices with maximum 6370 bytes distributed RAM. The FPGA contains 864 DSP48E1 slices
and has 1824 18kb RAM blocks and 912 36kb RAM blocks. That is a total memory of 32832kb.
3 Configuring FPGAs
FPGAs are not programmed directly. Synthesis tools translate the code into bit stream, which is downloaded
to the configuration memory of the FPGA. Commonly, hardware description languages (HDL)
are use to configure the device. But resent trends also offer the possibility to high level languages.
Furthermore, there are library based solution which are optimized for a specific device.
Hardware description language Using a HDL is the most common approach to configure a FPGA. There
are two dominating languages, VHDL and Verilog. Both languages have the power of international
standards and working groups behind and are similar powerful. VHDL was developed in the 1980s
by the Department of Defense and is essentially as subset of ADA with extensions for describing
hardware. Verilog was originally a C-like programming language to model hardware and later
became IEEE standard like VHDL. The languages support different levels of abstraction, but most
configurations are done at the register transfer level (RTL). The design resembles soft development
more than hardware development, but there are big differences. Software programs have a sequential
execution model and the correctness of the program depends on the sequential executed commands.
Decision points are very common. Furthermore, programmer does not have to care about data flow
between registers and memory. Hardware designs consists of several block of hardware running in
parallel. The designer tries to avoid decision points, because of performance reasons. The wires
for data movement have to be explicitly written on the FPGA. To configure with a FPGA with
HDL a developer needs two programs. A tool that allows the programmer to test and simulate a
configuration on a PC and the synthesis tool that is needed to convert the HDL program into a bit
stream and download it to the FPGA.
High level language There are also approaches using high level languages that make designing FPGA
application more alike software development.
SystemC is a C++ library that allows to specify and simulate hardware processes using a C++
syntax.
Handel-C is an extended subset of ANSI C that allows developer to specify their designs with C. It
can be synthesized directly for implementation on FPGAs.
With Accelchip it is possible to generate VHDL or Verilog code block for common MATLAB DSP
functions.
Library-based solutions There functions that are needed in many FPGA design. For those functions
are already optimized solutions available. Therefore the FPGA manufacturer Xilinx and Altera
offer parameterized macros to generate code for common blocks such as arithmetic functions or
specialized memories. The output of the macros is HDL code that can be included in the developers
synthesis process. This reduces the development time.
13-07-2012, 11:46 AM
Post: #2
RE: Field Programmable Gate Array (FPGA) full report
Field Programmable Gate Array



.ppt  fpga.ppt (Size: 1.26 MB / Downloads: 29)

History

Programmable Read Only Memory (PROM)
fuse programming
n- address i/p can implement n i/p logic fun.
Problem:
Area efficiency.

Programmable Logic Array (PLA)
Programmable AND plane followed by programmable or wired OR plane.
Sum of product form
Problem :
Two level programming adds delay


FPGA


A Field Programmable Gate Array (FPGA) is a Programmable Logic Device(PLD) with higher densities and capable of implementing different functions in a short period of time.

Topics covered:-
FPGA Overview
Logic Block
FPGA Routing Techniques
Programming Methodology
FPGA Design Flow


Other FPGA Advantages


Manufacturing cycle for ASIC is very costly, lengthy and engages lots of manpower
Mistakes not detected at design time have large impact on development time and cost
FPGAs are perfect for rapid prototyping of digital circuits
Easy upgrades like in case of software
Unique applications


Altera logic block:-

Wide fan-in
Up to 100 i/p AND gate fed into OR gate with 3-8 i/ps

Advantage:-

Few logic block can implement the entire functionality
Less area required

Disadvantage:-

If i/ps are less, usage density of block will be low
Pull up devices consume static power


FPGA Routing Techniques


Comprises of programmable switches and wires
Provides connection between I/O blocks, logic blocks etc.
Routing decides logic block density and area consumed

Different routing techniques are:-
Xilinx Routing architecture
Actel routing methodology
Altera routing methodology
Rating Field Programmable Gate Array (FPGA) full report Options
Share Field Programmable Gate Array (FPGA) full report To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : field programmer gate array seminar topics, pdf fpga report, performance of field programmable gate arrays, fpga full seminar report, lut iobs dsp48e1, a seminar report on field programming gate array, seminar report on programmable logic array, seminar report on field programmable gate array, full seminar on fpga pdf, seminar topic on fpga, fpga full seminar report free download, seminars topics on programmable logic arrays, abstact on fpga lookup tables, full seminar pdf for computer science, ppt fpga command line configuration, field programmable gate array, seminar topic from field programmable gate array system, reconfigurable fpga structure,

[-]
Quick Reply
Message
Type your reply to this message here.


Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  WISENET-Wireless Sensor Network (Download Seminar Report) Computer Science Clay 86 62,268 18-10-2014 10:22 AM
Last Post: mkaasees
  BLUE BRAIN TECHNOLOGY SEMINAR REPORT project maker 0 118 11-10-2014 10:11 AM
Last Post: project maker
  Retina Based Mouse Control seminar report project maker 0 75 10-10-2014 12:14 PM
Last Post: project maker
  Microencapsulation seminar report project maker 0 54 10-10-2014 10:55 AM
Last Post: project maker
  a study on organisation seminar report project maker 0 54 10-10-2014 09:56 AM
Last Post: project maker
   ROADS FROM PLASTIC WASTE SEMINAR REPORT project maker 0 68 09-10-2014 11:53 AM
Last Post: project maker
  Data Integrity Proofs in Cloud Storage seminar report project maker 0 63 09-10-2014 11:14 AM
Last Post: project maker
  3D SEARCHING SEMINAR REPORT project maker 0 68 09-10-2014 10:35 AM
Last Post: project maker
  Game Theory for Network Security seminar report project maker 0 66 08-10-2014 01:56 PM
Last Post: project maker
  HAPTIC TECHNOLOGY SEMINAR REPORT project maker 0 70 08-10-2014 12:34 PM
Last Post: project maker
This Page May Contain What is Field Programmable Gate Array (FPGA) full report And Latest Information/News About Field Programmable Gate Array (FPGA) full report,If Not ...Use Search to get more info about Field Programmable Gate Array (FPGA) full report Or Ask Here

Options: