Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)
Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
01-03-2011, 12:39 PM
Post: #1
GSM (SMS) Controlled DC Motor

.doc  GSM (SMS) Controlled DC Motor.doc (Size: 135 KB / Downloads: 252)
GSM (SMS) Controlled DC Motor
INTRODUCTION

GSM (SMS) Controlled DC Motor is automatic control system which capable of receiving a set of command instructions in the form of Short message service and performs the necessary actions like Start , Stop and speed control. We will be using a dedicated modem/mobile at the receiver module i.e. with the robot it self and send the commands using SMS service as per the required actions.
The mobile unit which is dedicated at the motor driver is interfaced with an intellectual device called Micro controller so that it takes the responsibility of reading the received commands in the form of SMS from the mobile unit and perform the corresponding predefined tasks such as motor start, stop, motor direction and speed control at different levels etc.
HARDWARE USED
1. AT command supporting GSM mobile phone.
2. 89S52 Microcontroller
3. Max 232 IC.
4. Motor Driver IC L293
5. Voltage regulator 78XX.
6. Diode IN4007
7. GSM Phone
SOFTWARE USED
1. Keil u-Vision 3.0

Keil Software is used provide you with software development tools for 8051 based microcontrollers. With the Keil tools, you can generate embedded applications for virtually every 8051 derivative. The supported microcontrollers are listed in the µ-vision
2. PRO51 Programmer Software
THEORY OF OPERATION

In this project we interfaced 8051 microcontroller with Motorola’s C168 GSM mobile phone to decode the received message and do the required action. The protocol used for the communication between the two is AT command.
The microcontroller continuously checks for SMS to take the decision for controlling the DC motor.
AT-Command set
The following section describes the AT-Command set. The commands can be tried out by connecting a GSM modem to one of the PC’s COM ports. Type in the test-command, adding CR + LF (Carriage return + Line feed = \r\n) before executing. Table gives an overview of the implemented AT-Commands in this application. The use of the commands is described in the later sections.
A BRIEF INTRODUCTION TO 8051 MICROCONTROLLER:
When we have to learn about a new computer we have to familiarize about the machine capability we are using, and we can do it by studying the internal hardware design (devices architecture), and also to know about the size, number and the size of the registers.
A microcontroller is a single chip that contains the processor (the CPU), non-volatile memory for the program (ROM or flash), volatile memory for input and output (RAM), a clock and an I/O control unit. Also called a "computer on a chip," billions of microcontroller units (MCUs) are embedded each year in a myriad of products from toys to appliances to automobiles. For example, a single vehicle can use 70 or more microcontrollers. The following picture describes a general block diagram of microcontroller.
89s52: The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory pro-grammer. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a powerful microcontroller, which provides a highly flexible and cost-effective solution to many, embedded control applications. The AT89S52 provides the following standard features: 8K bytes of Flash, 256 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM con-tents but freezes the oscillator, disabling all other chip functions until the next interrupt
20-04-2011, 04:05 PM
Post: #2
RE: GSM (SMS) Controlled DC Motor

.doc  GSM (SMS) Controlled DC Motor.doc (Size: 136.5 KB / Downloads: 142)
GSM (SMS) Controlled DC Motor
INTRODUCTION

GSM (SMS) Controlled DC Motor is automatic control system which capable of receiving a set of command instructions in the form of Short message service and performs the necessary actions like Start , Stop and speed control. We will be using a dedicated modem/mobile at the receiver module i.e. with the robot it self and send the commands using SMS service as per the required actions.
The mobile unit which is dedicated at the motor driver is interfaced with an intellectual device called Micro controller so that it takes the responsibility of reading the received commands in the form of SMS from the mobile unit and perform the corresponding predefined tasks such as motor start, stop, motor direction and speed control at different levels etc.
HARDWARE USED
1. AT command supporting GSM mobile phone.
2. 89S52 Microcontroller
3. Max 232 IC.
4. Motor Driver IC L293
5. Voltage regulator 78XX.
6. Diode IN4007
7. GSM Phone
SOFTWARE USED
1. Keil u-Vision 3.0
Keil Software is used provide you with software development tools for 8051 based microcontrollers. With the Keil tools, you can generate embedded applications for virtually every 8051 derivative. The supported microcontrollers are listed in the µ-vision
2. PRO51 Programmer Software
THEORY OF OPERATION
In this project we interfaced 8051 microcontroller with Motorola’s C168 GSM mobile phone to decode the received message and do the required action. The protocol used for the communication between the two is AT command.
The microcontroller continuously checks for SMS to take the decision for controlling the DC motor.
AT-Command set
The following section describes the AT-Command set. The commands can be tried out by connecting a GSM modem to one of the PC’s COM ports. Type in the test-command, adding CR + LF (Carriage return + Line feed = \r\n) before executing. Table gives an overview of the implemented AT-Commands in this application. The use of the commands is described in the later sections.
A BRIEF INTRODUCTION TO 8051 MICROCONTROLLER:
When we have to learn about a new computer we have to familiarize about the machine capability we are using, and we can do it by studying the internal hardware design (devices architecture), and also to know about the size, number and the size of the registers.
A microcontroller is a single chip that contains the processor (the CPU), non-volatile memory for the program (ROM or flash), volatile memory for input and output (RAM), a clock and an I/O control unit. Also called a "computer on a chip," billions of microcontroller units (MCUs) are embedded each year in a myriad of products from toys to appliances to automobiles. For example, a single vehicle can use 70 or more microcontrollers. The following picture describes a general block diagram of microcontroller.
89s52: The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory pro-grammer. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a powerful microcontroller, which provides a highly flexible and cost-effective solution to many, embedded control applications. The AT89S52 provides the following standard features: 8K bytes of Flash, 256 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM con-tents but freezes the oscillator, disabling all other chip functions until the next interrupt
03-03-2012, 12:00 PM
Post: #3
RE: GSM (SMS) Controlled DC Motor
to get information about the topic dc motor speed and direction control using gsm mobile full report ppt and related topic refer the link bellow
http://seminarprojects.com/Thread-speed-...-using-gsm

http://seminarprojects.com/Thread-gsm-sm...d-dc-motor
Rating GSM (SMS) Controlled DC Motor Options
Share GSM (SMS) Controlled DC Motor To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : gsm sms controlled dc motor ppt, dc motor speed control using gsm project report, microcontroller 89s52 for gsm, ppt on gsm controlled motor, ppt for sms controlled dc motor free download, ppt for sms controlled dc motor, cell phone controlled dc motor, speed control of dc motor using sms using 8051 microcontroller, how we can use mobile in control speed of motor, how to start stop motor using mobile, gsm control d c motor, gsm sms controlled dc motor projects, project report on gsm controlled dc motor pdf, controlling of dc motor using sms project using microcontroller 8051, ppt on sms controlled motor, speed control of dc motor through sms using gsm,

[-]
Quick Reply
Message
Type your reply to this message here.


Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  WIRELESS CONTROLLED MINE DETECTING ROBOT projects wizhard 12 10,747 07-01-2014 10:02 AM
Last Post: seminar projects maker
  Case study of Tata Motor Acquisition of Jaguar and Land Rover seminar addict 2 3,140 02-09-2013 09:48 AM
Last Post: study tips
  Ultrasonic Sensor Based DC Motor Control Using LabVIEW seminar class 3 4,591 29-08-2013 09:47 AM
Last Post: study tips
  Motor Control Using Triac Application Note study tips 0 331 07-06-2013 04:22 PM
Last Post: study tips
  DTMF Controlled Robot pdf study tips 0 216 03-06-2013 02:30 PM
Last Post: study tips
  switched reluctance motor full report project report tiger 5 7,046 05-04-2013 09:37 AM
Last Post: study tips
  History of Power Electronics for Motor Drives in Japan pdf project girl 0 294 25-01-2013 12:44 PM
Last Post: project girl
  2A Dual Motor driver module with PWM control [RKI-1172] project girl 0 261 20-12-2012 03:20 PM
Last Post: project girl
  WIRELESS RF CONTROLLED ROBOT PPT project girl 0 260 10-12-2012 03:06 PM
Last Post: project girl
  Ultrasonic Motor computer science crazy 3 3,265 10-12-2012 12:09 PM
Last Post: seminar tips
This Page May Contain What is GSM (SMS) Controlled DC Motor And Latest Information/News About GSM (SMS) Controlled DC Motor,If Not ...Use Search to get more info about GSM (SMS) Controlled DC Motor Or Ask Here

Options: