Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)
Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
24-01-2013, 10:43 AM
Post: #1
SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS
SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS



.docx  SINGLE PHASE.docx (Size: 15.1 KB / Downloads: 24)


AIM:

To Verify the operation of single phase AC Voltage controller with R and RL Loads and
to observe the output and input waveforms

APPARATUS:

S.No EQUIPMENT Qty
1. I-φ Transformer 1
2. I-φ AC voltage controller
power circuit with firing unit
3. Voltmeters(MI meters) 2
4. Rheostat 1
5. Inductive load 1
6. CRO with (1:10) Probe 1
7 Patch cards

THEORY:

AC voltage controller’s are thyristor based devices ,which converts the fixed Ac
voltage into variable AC voltage with same frequency .The circuit diagram of Single phase AC
voltage controller is shown in figure .It consists of two SCR’s connected in anti parallel. The
input and output voltage waveforms are also shown. The SCR’s are gate controlled and gate
pulses are obtained from firing unit.

For R-Load:

For the first half cycle of input voltage waveform SCR T1 conducts and gives
controlled output to load. During the other half cycle of input voltage waveform SCR T2
conducts .During the Positive half cycle T1 is triggered at a firing angle of wt= α .T1 starts
conducting and source voltage is applied to the load from α to π. At wt= π both Vo and Io
falls to zero. Just after wt= π, T1 is reverse biased and therefore it is turned off by self
commutation.

For RL –Load:

During the first half cycle wt = 0 to π SCR T1 is forward biased and is
triggered at wt=α and output current starts building up through load .At wt=π, load and
source voltage are zero. But the output current is not zero because of inductive load. At
wt=(β>π), the load current reduces to zero, angle β is called extinction angle. After wt =
π, SCR T1 is reverse biased, but does not turn off because the output current is not zero.
At wt=β, only when output current is zero T1 turns off.
During the negative half cycle SCR T2 is forward biased and is triggered at
wt = π+α. The output current flows through the load in reverse direction. The operation
of SCR T2 is similar as that of SCR T1 during the period wt = π+α to wt = (2β-α) but in
the negative direction. At wt= ( 2β-α) the SCR t2 is commutated and the next positive
half cycle will be regulated by SCR T1. In this way the AC Voltage controller will be
useful for regulating the AC voltage.

PROCEDURE:

A) For R-Load:
1. Connect the circuit as shown in figure.
2. Verify the connections from the lab instructor before switch on the supply.
3. Keep the rheostat position value given by the lab instructor
4. Switch ON the CRO and calibrate it with the input voltage.
5. Switch on the power circuit and firing circuit.
6. Observe the output voltage waveform in the CRO.
7. Note down the reading of α from the CRO and Vo from the voltmeter
8. Also calculate the theoretical value of output voltage from the formula and
compare it with the practical value of the output voltage, which is observed from
the voltmeter.
9. Repeat the above process from step 6 to 8 for various firing angles.
Rating SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS Options
Share SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : ac voltage controller, theory of single phase a c voltage controller with r load, ppt slides on single phase ac voltage controller, single phase ac voltage controller theory, single phase ac voltage controller with rl load waveforms, single phase ac voltage controller project file, circuit design of single phase ac voltage controller, ac voltage controller using r load, single phase ac voltage controller with rl load pratical experiment, ppt of single phase ac voltage controller with r and rl load, explain single phase ac ac controller with rl load, single phase ac voltage controller with r and rl load experiment pdf, 1 voltage controller with rl load,

[-]
Quick Reply
Message
Type your reply to this message here.


Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Voltage Flicker Compensation using STATCOM seminar report project maker 0 60 18-09-2014 12:39 PM
Last Post: project maker
  VOLTAGE STABILITY ENHANCEMENT BY USING STATCOM SEMINAR REPORT seminar code 0 95 12-09-2014 12:49 PM
Last Post: seminar code
  HIGH VOLTAGE DIRECT CURRENT TRANSMISSION SEMINAR REPORT seminar code 0 123 11-09-2014 12:57 PM
Last Post: seminar code
  Unified Power Flow Controller (UPFC): Modeling and Analysis Seminar Report seminar code 0 91 04-09-2014 11:02 AM
Last Post: seminar code
  Voltage Flicker Compensation using STATCOM project maker 0 49 29-08-2014 02:23 PM
Last Post: project maker
  Cordless Power Controller project maker 0 88 29-08-2014 12:39 PM
Last Post: project maker
  SIMULATION OF DC VOLTAGE REGULATOR USING SCR project girl 3 576 28-08-2014 07:01 PM
Last Post: Guest
  SERVO CONTROLLED VOLTAGE STABILIZER SEMINAR REPORT seminar code 0 120 23-08-2014 04:59 PM
Last Post: seminar code
  Grid Voltage Regulation Utilizing Storage Batteries in PV Solar seminar ideas 10 7,861 12-08-2014 05:29 PM
Last Post: tusahr
  High voltage engineering seminar code 0 123 27-06-2014 11:28 AM
Last Post: seminar code
This Page May Contain What is SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS And Latest Information/News About SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS,If Not ...Use Search to get more info about SINGLE PHASE AC VOLTAGE CONTROLLER WITH R & RL LOADS Or Ask Here

Options: